Graule MACHINERY

Graule EMS Cover Replacement / Emergency Stop Cover Flap

Common on Most Graule Machines, ZS170N, ZS200N, ZS135N, KS Mitre Saw, Graule AKF End Millers. Etc.

Can find uses on other machines with the same tripus start / stop box

Top is usually smashed off and only the yellow / Grey surround remains once damaged

** COLOUR MAY DIFFER DEPENDING ON STOCK**

Can be Yellow and red or Grey and Black, Identical make and dimensions

Brand: Tripus

Easy to change just 2 Screws under the cover

All Prices Plus VAT and Delivery

Graule Cross Cut Saws Table / Bed Insert

Consumable Part for the Small Section of the Graule Cross Cut Saws Table Right near the Saw Blade (Bit that gets the Most wear)

Saves Changing the complete table so often

Good Practice to change regularly once worn to prevent smaller off cuts falling into the blade

Fits: Graule ZS170N, Graule ZS200N, Graule ZS135 ETC.

Easy to change with just 2 Screws

All Prices Plus VAT and Delivery

Replacement Saw Table for Graule ZS170N, once the table becomes too warn out and changing the insert is no longer enough its best to replace the whole table

Complete with Table Insert

Made from High Quality Ply Wood, Holes Pre Drilled for Bolt on fitment

Ref: 08.02 04126000, table, wood cpl. with insert

All Prices Plus VAT and Delivery

Pair of Genuine Graule ZS170N Replacement Drive belts (2 Belts are in the Machine)

Price per Belt £29.85+VAT

It is Recommended to change both belts in the machine even if only one has snapped as they will wear down differently and be slightly different sizes, Tensioner for belts is under the motor

Branding May Vary, but will be the same Genuine Graule product

For Type 135 (N) - 170 (N)

All Prices Plus VAT and Delivery

Pair of Genuine Graule ZS200N / ZS200 Replacement Drive belts (2 Belts are in the Machine)

Price per Belt £39.62+VAT but sold as a Pair

It is Recommended to change both belts in the machine even if only one has snapped as they will wear down differently and be slightly different sizes, Tensioner for belts is under the motor

Ref. 8904-2710-11M710-2

All Prices Plus VAT and Delivery

Graule Contactor Switch

Replacement Switch part for Start / Stop Boxes on Most Graule Machines

The Contactor is the part inside the Switch Box on Graule Saws and End Millers that switches the power on and off so is often the fault if the machine will not start

Typical Symptoms of a new contactor needed are:

• Machine will only keep running if you press hold the button in (Coils Gone)

• Machine Will run but gets hot or runs backwards

• Motor will Hum or Buzz but not fully Start

• Motor Wont run at all

Coil Voltage on all machines with these contactors is 240V (Uses the Neutral), so whether your machine is Single Phase or 3 Phase like a KS for example its the same contactor

Contactor Fits: ZS200N, ZS200, ZS170N, ZS170, ZS135, AK4 End Millers, AK6 End Millers, KS Mitre Saws etc.

Colours can Vary, Some are Black some are a Terracotta Red its the Same Part

All Prices Plus VAT and Delivery

Graule ZS200N Horizontal Lock off handle assembly

Graule ZS200N specific part

Some Adjustment will be needed when fitting just so the lock off point is correct for the handle, a little fiddling with thread height positions is all that is needed

Made in Germany

All Prices Plus VAT and Delivery

UK Shipping only

Graule ZS170N Horizontal Lock off handle assembly

Graule ZS170N specific part, it is a different part for the ZS170 model which doesnt not compound cut

Some Adjustment will be needed when fitting just so the lock off point is correct for the handle, a little fiddling with thread height positions is all that is needed

Made in Germany

All Prices Plus VAT and Delivery

UK Shipping only

Genuine Graule Replacement Back Fences Set for the ZS170N

Pre Cut for easy fitting

Replaces worn and cut fences to ensure a safe and accurate cut

Bolt on item, easy to change

Supplied as a Pair of left and right fences

ALL PRICES PLUS VAT AND DELIVERY

Graule ZS170N Spring Return Unit Complete with Wire Rope for easy repair

Pre-tensioned Cable makes this an easy bolt on repair to Graule ZS170N Machines with Broken return units which no longer return the saw head automatically . Just bolt on the unit to the back of the machine and bolt down the wire rope hoop to the moving head

Ref. 09.13/ 04170500 / spring installation cpl.

All Prices Plus VAT and Delivery

Graule ZS170N Adjustable Front Guard

Replacement for missing guard or for some older machines which never had the guard fitted

Comes with fitting Instructions

All Prices Plus VAT and Delivery

Very Good Quality Aftermarket Blade to Suit the Graule ZS170N Cross Cut Saw

N5EAM13L-420-100-4.0/3.4 Graule ZS170N Saws

• 420mm Dia

• 100T

• Negative Rake

• Suitable for Aluminium and Plastics

• 40mm Bore

• Made in Sweden

All Prices plus VAT and Delivery

Graule ZS170N Cross Cut Saw Head Release Latch Old Style

Replacement Latch and lock block as pictured

Latch locks head in place when returned

Some older versions have a slightly different main body part which is more of a U section but same fitment

There is a newer twist grip latch which is sold separately and incompatible with this style

All Prices Plus VAT and Delivery

Graule ZS170N / ZS200N Replacement Wire Rope for Head Return

Wire Cable replacement for the Return spring unit on Graule Cross Cut Saws

Over time the old Cable will become worn / frayed and can snap

Spring will require re-tensioning once replaced, please call if you have any questions fitting

All Prices Plus VAT and Delivery

Graule ZS170N Outer Blade Flange and Left Hand Blade Bolt set

Replacement Blade Bolt and Blade Flange for ZS170N

ALL PRICES PLUS VAT AND DELIVERY

Graule KS Head Return Spring

Replacement Part for The Graule KS Head Return

Styles May Vary, Newer Springs Tend to have less coils but are slightly wider (Same Fitment)

All Prices Plus VAT and Delivery

Graule ZS170N Drop in Pin for 45 / 90 degree angle locating

Steal pin for Quick angle location on Graule ZS170N

ALL PRICES PLUS VAT AND DELIVERY

Replacement Fan for Graule ZS170N , ZS135 and KS Mitre Saws

Fan also Acts as part of the Braking System it has a brake pad type backing which will wear out over time

*EXTREME CARE TO BE USED WHEN FITTING*

If you are unsure about fitting please give us a call or email

Fan is very Fragile and easily broken when fitting, Self Install at own risk

Once fitted its very hard to remove fan without damaging Fan

Applying fan too far on the shaft will also result incorrect function of the braking system, best method is so go slowly and test repeatedly until correct braking function is achieved

All Prices Plus VAT and Delivery

Graule End Miller type Return Spring

Graule End Miller Replacement Return Spring for Graule AKF 4 Type End Milling Machines

Spring sometimes used on some very old Graule ZS170N Cross Cut Saws

All Prices Plus VAT and Delivery

Graule ZS170N / ZS135N

Lock handle for locking off the Horizontal angle position

Parts Include:

Graule Part 02.04 GRIP D10/M8

Graule Part 02.08 NUT TR16

All Prices Plus VAT and Delivery

Graule ZS200N Replacement Saw Table

Once the table becomes too warn out and changing the insert is no longer enough its best to replace the whole table

Complete with Table Insert

Made from High Quality Ply Wood, Holes Pre Drilled for Bolt on fitment

Ref: 08.02 wood cpl. with insert

All Prices Plus VAT and Delivery

Graule ZS200N Spring Return Unit Complete with Wire Rope for easy repair

Pre-tensioned Cable makes this an easy bolt on repair to Graule ZS200N Machines with Broken return units which no longer return the saw head automatically . Just bolt on the unit to the back of the machine and bolt down the wire rope hoop to the moving head

Ref. 09.13/ 04170500 / spring installation cpl. ZS200N

Part used on: ZS 200 Saws, AKF 6 End Millers and AS Types

All Prices Plus VAT and Delivery

Graule ZS170N / ZS170 Linear Bearings set (x4 Bearings)

Genuine Graule Product from Germany

Set of 4 Bearings for a Graule ZS170N Cross Cut Saw

Replaces Bearings in the backwards / forwards cutting operation of the saw, over time they can become worn and need replacing to ensure free and easy movement

When fitting ensure the locating pin is properly aligned with the bearing

Ref: 04180202 / 09.03

Cutting and mitre circular saws type ZS 85 to ZS170N

(6-row ball bushing)

With these machines, the Kpl. Saw carriages can be removed from the guide to the front.

•Disconnect the machine from the electrical network and remove the saw blade Hang the retraction tedre (old system) or the steel cable of the rope re circulation on the carriage.

•Install the front end strip at the end of the shaft If the machine has a hydraulic feed brake, remove it as well

•Loosen the side grub screw (top or bottom) slightly on the ball socket holder so that the preload of the ball bushing is releasedCAREFULly pull the complete saw head forward from the guide shafts. Be careful not to warp the guide elements. It may be helpful if this work is carried out by 2 men. Here one man holds the weight and the other man pays attention to a straight guide when playing.Alternatively, the saw head can only be pulled forwards or backwards from the guide so far that only 2 ball bushings are released and the carriage with the other twoBall rifles are still held on the guide.Remove ball rifles from holders. To do this, turn the grease nipple back.Insert a new ball bushing and fix it with grease nipples. Pay attention to the correct installation position of the ball bushing (fixing hole). Leave the cardboard sleeve in the ball bushing!

•Gently slide onto guide shafts, pushing out the cardboard sleeve.ATTENTION: Do not warp under any circumstances, because then the ball rifles burst!!.

•Screw in the side grub screw until you feel that the ball bushing is being tensioned .As soon as the grub screw comes into pressure, only tighten slightly.ATTENTION: No large preload must be applied to the ball bushing.

ALL PRICES + VAT and Delivery

Graule ZS200 / ZS200N Linear Bearings (Set of 4)

Genuine Graule Product from Germany

Set of 4 Bearings for a Graule ZS200 Cross Cut Saw

Replaces Bearings in the backwards / forwards cutting operation of the saw, over time they can become worn and need replacing to ensure free and easy movement

When fitting ensure the locating pin is properly aligned with the bearing

Ref: 04180202 / 09.03

Cutting and mitre circular saws type ZS200 /N

(8-row ball bushing)

With these machines, the Kpl. Saw carriages can be removed from the guide to the front.

•Disconnect the machine from the electrical network and remove the saw blade Hang the retraction tedre (old system) or the steel cable of the rope re circulation on the carriage.

•Install the front end strip at the end of the shaft If the machine has a hydraulic feed brake, remove it as well

•Loosen the side grub screw (top or bottom) slightly on the ball socket holder so that the preload of the ball bushing is releasedCAREFULly pull the complete saw head forward from the guide shafts. Be careful not to warp the guide elements. It may be helpful if this work is carried out by 2 men. Here one man holds the weight and the other man pays attention to a straight guide when playing.Alternatively, the saw head can only be pulled forwards or backwards from the guide so far that only 2 ball bushings are released and the carriage with the other twoBall rifles are still held on the guide.Remove ball rifles from holders. To do this, turn the grease nipple back.Insert a new ball bushing and fix it with grease nipples. Pay attention to the correct installation position of the ball bushing (fixing hole). Leave the cardboard sleeve in the ball bushing!

•Gently slide onto guide shafts, pushing out the cardboard sleeve.ATTENTION: Do not warp under any circumstances, because then the ball rifles burst!!.

•Screw in the side grub screw until you feel that the ball bushing is being tensioned .As soon as the grub screw comes into pressure, only tighten slightly.ATTENTION: No large preload must be applied to the ball bushing.

ALL PRICES + VAT and Delivery UK Shipping only

Assembly of Parts for Graule ZS170N / ZS200N Head Release Safety Latch as pictured

New Type Latch “Twist Grip” Activation

All Prices Plus VAT and Delivery

Replacement / Repair Scale Tape for Double Mitre Saws and Other Machines

Typically when the Machines original Scale tape becomes worn this can be stuck over the top to renew the machine (Clean Surface before Sticking)

Can Also Be used on Length Stops and Benches etc.

5 Metre Length

Left to Right ( counts up in the traditional way)

Self Adhesive

Plastic Coated for Durability and long life

13mm Dia

Steel Core ( Use Tin Snips / Similar to Trim To Size)

Is Completely Flat

All Prices Plus VAT and Delivery

Can Be ordered in Right to left (Other hand) or in Longer Lengths (10M) Please Call or Email